How to Turn on Vulcan Gas Heater / Pilot Light

How to Turn on Vulcan Gas Heater / Pilot Light

Do You Find That Your Vulcan Pilot Light Goes Out More Often Than It Should?

If you find you are having to re-light your pilot light often, your Vulcan gas water heater may need repair

Get Help From a Professional Vulcan Gas Hot Water Expert

We’ll show you how to start / light your Vulcan gas water heater shortly, but if you find your Vulcan pilot light goes out often, you should seriously consider bringing in a professional to diagnose and fix the issue.

A pilot light that continues to go out is a sign of a potentially bigger issue and the wisest thing to do is to get an expert on it immediately.

VIDEO TRANSCRIPTION

How to Light Vulcan Gas Heater:

In your Vulcan 4 Star gas water heater, there is a small pilot flame that should remain alight at all times. This small flame lights the main burner whenever water in the tank needs heating. If you can’t get hot water it may be because the pilot flame has gone out and thus, there’s no way for the main burner to be relit. This could occur for a number of reasons such a strong winds, gas maintenance work carried out in the street or an empty LPG cylinder. Today, we’ll show you the safe correct way to relight your gas water heater. As you’ll see, it’s quite easy. However, it is vital that you follow this procedure exactly to prevent a buildup of gas, which if ignites, can cause serious injury.

Before beginning, ensure all flames and ignition sources including cigarettes and lighters are kept well away from the area.

Check For Gas Leaks

First, remove the access panel. The instructions for relighting are clearly laid out inside this panel. It is important to ensure there are no gas leaks. This is best done by simply smelling for gas, especially down the floor level where gas can accumulate. If you smell gas, turn the gas control knob to the “off” position. Shut off the isolation valve in the gas line. Leave the area and call for a qualified service technician.

Turn Off Control And Wait Five Minutes

Once you’ve confirmed there are no gas leaks, turn the gas control knob fully clockwise to the “off” position. You should feel the control knob clicking to the off position. Do not use tools to turn the knob. If you cannot turn the knob by hand call a service technician or licensed gasfitter. It is vital at this point that you wait five minutes for any unburned gas to escape. If you do not wait the full five minutes, residual gas may ignite and cause serious injury.

Light The Pilot

Once five minutes have elapsed, we’re ready to light the pilot using the igniter button. You must remember that this button produces a spark that will ignite any gas that is nearby. This is why it is so important that you turn the control knob to off and wait five minutes for gas to dissipate before every time you use the igniter button. Next, turn the control knob to the pilot position. This is the symbol that looks like a starburst. Depress the control knob fully and keep holding the knob down to allow sufficient gas to flow to the pilot light. After waiting for 30 seconds with the control knob held down, keep the control knob down and now press the igniter button repeatedly for about 40 seconds. Keep your face clear of the combustion chamber. At this point, the pilot should be alight. It is important that you continue to hold the control knob down for a further 20 seconds for the pilot light to establish itself. You can now release the knob. Once the control knob is released, check that the pilot is alight. Do this by looking into the combustion chamber just below the gas control. The pilot will be visible as a very small blue flame.

If The Pilot Is Not Alight

If the pilot is not alight, it is vital that you turn the gas control knob to “off” then once again, wait for five minutes for the gas to disperse. Once five minutes is up, begin the pilot lighting process again from the start- back where we turn the control knob from the “off” position to the pilot position.

Once The Pilot Is Alight

Once the pilot is alight, it’s important for your safety that you remove your face from directly in front of the combustion chamber opening. Then turn the control knob anti-clockwise to at least five. This will allow the main burner to light whenever the water needs heating. When the main burner lights up, it can be a little noisy for the first 2 to 5 seconds, this is perfectly normal. It will very soon settle down to a quiet flame. You can now replace the access panel.

Let’s Review

As you can see, it’s a straightforward procedure but does need to be followed exactly:

  1. Turn the control knob to off.
  2. Wait five minutes for gas to disperse.
  3. Now turn the control knob to pilot.
  4. Press the control knob down for 30 seconds.
  5. Keep holding the control knob down; press the igniter repeatedly for 40 seconds.
  6. Keep holding the control knob down for a further 20 seconds while the pilot establishes itself.
  7. Check the pilot. If the pilot is alight, pull your face away and turn the control knob to at least five.

Remember, if at any time during the lighting process the pilot flame is not alight when you expect it to be, turn the gas control to “off” and wait 5 minutes before starting again. If you’re unsure of the lighting process, or the burner does not light as expected; call Vulcan Service on 131031. Thank you for watching and we hope you enjoy many years of safe, steady hot water.

Book Online

Get an obligation free quote or email us on [email protected] or call 1300 465 463.

Fast, Same Day Service 24/7

Emergency Plumbing and Electrical